Fluke 190 Series II, 2 and 4 Channel Instruments V09.00 | Fluke
English

Fluke 190 Series II, 2 and 4 Channel instruments with firmware version V09.00 onwards

Firmware Release V11.46 »
Firmware Release V11.46 Readme »

For Fluke 190 Series II, 2 and 4 Channel instruments with firmware version V09.00 onwards. The firmware release V11.46 has the following improvements:

Firmware version V11.45

For Fluke 190 Series II, 2 and 4 Channel instruments with firmware version V09.00 onwards. The firmware release V11.45 has the following improvements:
  • Resolved issue with data storage of set-up files on USB-flash drives

Firmware version V11.44

The firmware release V11.44 has the following improvements:
  • Improved trigger delay handling for fastest timebase settings (scope mode).
  • Production related improvement.

Firmware version V11.43

For Fluke 190 Series II, 2 and 4 Channel instruments with firmware version V09.00 onwards. The firmware release V11.43 has the following improvements:
  • Fixed issue where some units could show unstable behavior for some channels, erroneous base line level and/or sometimes incorrect amplitude of waveform. This only applies to some units that have '2516' at the end of the Subversion information that is visible when selecting User key, F3=Version&Cal.
  • Fixed issue with channel setting replication so that auto/manual ranging is now copied as well. Channel replication is selected by push and hold channel key and push another channel key.
  • Fixed issue that could lead to disappearing channel ground indication on left of display when waveform is moved to bottom of screen.

Firmware version V11.42

The firmware release V11.42 has the following improvement:

  • Production related improvements to support new component

Firmware version V11.41

The firmware release V11.41 has fixed the following issues:

  • Improved speed of acquisition for replay and pass/fail testing
  • Fixed issues with pass/fail testing and replay playback
  • Fixed issues with spectrum display
  • Fixed issue with BWL indication in meter mode
  • Fixed issue with rounding frequency results

Firmware version V11.40

The release V11.40 update has fixed the following issues:

  • Improved speed of acquisition for replay and pass/fail testing
  • Fixed issues with pass/fail testing and replay playback
  • Fixed issues with spectrum display
  • Fixed issue with rounding frequency results
  • Fixed issue with BWL indication in meter mode

Firmware version V11.30

For 190 Series II, 2 and 4 Channel ScopeMeter test tools with version V09.00 onwards. The release V11.30 update has fixed the following issues (link to file download V11.30):

  • Fixed potential startup problem related to no traces on screen, or in the 4 Channel version no accessible C&D channels (*)
  • Fixed issues in storing and reading of ScopeRecord and Trendplot data as .CSV to USB
  • Fixed issue when ScopeMeter was turned off in TrendPlot mode with cursors on (*)

    Before the release of V11.30 this issue could be solved by following the below given steps:

    • Switch off the ScopeMeter test tool
    • Disconnect the power supply

    Wait for 5 minutes before continuing with the following steps:

    • Connect the power supply
    • Switch on the ScopeMeter test tool
    • Insert the battery pack (The battery will be charged)

Firmware version V11.20

For 190 Series II, 2 and 4 Channel ScopeMeter test tools with version V09.00 onwards. The release V11.40 update has fixed the following issues:

  • Ability to open saved waveforms of V10.0 or later
  • Fixed .BMP format problem when copying images from INT to USB
  • Prevent locking of instrument when data is copied from USB stick and no stick is present

Firmware version V11.10

For 190 Series II, 2 and 4 Channel ScopeMeter test tools with version V09.00, V10.4X or V11.0. The release V11.10 update addresses bug fixing and the possibility to store waveforms from within the ScopeMeter test tool on to a USB-stick as a CSV-file, then open this using FlukeView or a spreadsheet program.

Firmware version V10.41

Fluke 190 Series II, 4 Channel Instruments with V10.40 Firmware, Safety Notice and Recall.

For 190 Series II, 4 Channel ScopeMeter test tools with version V10.40 firmware has a measurement reading decimal point display problem that requires a firmware update to V10.41 or higher to avoid a potential user safety risk.

GPL Offer